The Puretec WH2-30 is a dual-stage whole-house filtration system designed for mains water supplies. It filters the incoming supply before water continues to applicable taps, showers and water-using fixtures throughout the property.
The current WH2-30-LF uses a Puretec PX05MP1 5 micron sediment cartridge followed by a Puretec CB10MP1 10 micron carbon block cartridge. Puretec lists the system for reduction of sediment, chlorine, unwanted taste and odour, chemicals and PFAS.
With a manufacturer-listed maximum flow rate of 30 litres per minute and a 1" BSP / 25 mm connection, the WH2-30 is intended for smaller-flow whole-house mains-water applications.
*Puretec's current warranty is 1 year parts and labour plus 9 years parts only. Replacement cartridges are excluded and warranty conditions apply.
The first stage uses Puretec's 5 micron graded polyspun sediment cartridge to reduce dirt, rust, sand, silt, algae and other suspended particulate matter.
The second stage uses Puretec's 10 micron bonded activated-carbon block cartridge for chlorine, unwanted taste, odour and sediment treatment.
The WH2-30 is designed for installation on the incoming mains-water line.
Water passes through the sediment cartridge first and then through the carbon stage before continuing through the downstream household plumbing.
This gives the property central sediment and carbon filtration rather than limiting treatment to one drinking-water outlet.
The PX05MP1 is a large-format MaxiPlus 4.5" × 10" graded polyspun sediment cartridge.
Puretec manufactures the cartridge from virgin polypropylene and lists it for general particulate reduction in mains-water applications.
Puretec lists a nominal 5 micron filtration rating.
Reduces suspended dirt and particulate rust in the incoming supply.
Provides depth filtration for suspended sand, silt and similar particulate material.
Puretec also lists suspended algae among the material targeted by the PX Series.
The media uses graded-density construction for depth filtration through the cartridge.
Puretec lists the individual PX05MP1 cartridge at up to 76 L/min; the complete WH2-30 system remains rated at 30 L/min maximum flow.
The second stage uses the CB10MP1, a MaxiPlus 4.5" × 10" bonded activated-carbon block cartridge.
Puretec lists this cartridge for reduction of chlorine, unwanted taste, odour and sediment.
Puretec lists a nominal 10 micron rating for the CB10MP1.
The bonded activated-carbon media provides chlorine reduction within its rated operating conditions.
Designed to reduce unwanted taste and odour in compatible mains-water applications.
The CB10MP1 uses a bonded carbon-block construction rather than loose granular media.
Puretec describes the cartridge as providing carbon treatment without release of carbon fines.
The individual CB10MP1 is rated by Puretec at 30 litres per minute, matching the WH2-30's listed maximum system flow.
Puretec's current WH2-30 product information identifies the complete system for mains-water filtration including:
The standard WH2-30 contains a sediment cartridge and carbon block. It does not contain a dedicated water-softening or scale-control stage.
If measurable hardness reduction or scale control is required, select a dedicated Puretec softener or scale-treatment system separately.
Puretec currently lists the WH2-30 with a maximum flow rate of 30 L/min and a 1" BSP / 25 mm connection.
This configuration is listed by Puretec for small to medium residences, although final sizing should be based on the property's actual simultaneous flow demand rather than a household label alone.
Puretec's current WH2-30 product specification lists a maximum pressure of 520 kPa.
The filtration system should be installed so it remains within the current manufacturer pressure specification.
Puretec describes the WH2-30 as a heavy-duty whole-house filtration system and currently lists an integrated rust-proof, anti-flex aluminium wall-mount bracket.
Separate sediment and carbon stages allow particulate pre-filtration before carbon treatment.
The system uses a 4.5" × 10" MaxiPlus carbon block for whole-house treatment.
The filtration assembly has no automatic valve, pump or regeneration mechanism.
The WH2-30 filtration process operates using the property's water pressure.
Puretec lists an integrated rust-proof, anti-flex aluminium mounting bracket.
Both treatment stages use separately replaceable genuine Puretec cartridges.
| Specification | Puretec WH2-30 |
|---|---|
| Current Model | WH2-30-LF |
| Water Source | Designed for mains water |
| Residence Guide | Small to medium |
| Filtration Type | Dual-stage whole-house filtration |
| Maximum Flow Rate | 30 L/min |
| Maximum Pressure | 520 kPa |
| Connection | 1" BSP / 25 mm |
| Stage 1 Cartridge | PX05MP1 |
| Stage 1 Rating | 5 micron, MaxiPlus 4.5" × 10" |
| Stage 2 Cartridge | CB10MP1 |
| Stage 2 Rating | 10 micron, MaxiPlus 4.5" × 10" |
| Electrical Power | Not required for filtration |
| Moving Parts | None in the filtration assembly |
| Warranty | 10 years – 1 year parts and labour plus 9 years parts only, excluding cartridges and subject to conditions |
| Feature | WH2-30 | WH2-35 |
|---|---|---|
| Stage 1 | PX05MP1 | PX05MP1 |
| Stage 2 | CB10MP1 | CB10MP1 |
| Maximum Flow | 30 L/min | 30 L/min |
| Connection | 1" / 25 mm | 1½" / 40 mm |
| Primary Difference | 25 mm plumbing connection | 40 mm plumbing connection |
Choose between these models according to the plumbing design and connection requirement rather than assuming the larger connection automatically means greater filtration performance.
| Feature | WH2-30 | WH2-55 |
|---|---|---|
| Cartridge Format | 4.5" × 10" MaxiPlus | 4.5" × 20" MaxiPlus |
| Sediment Cartridge | PX05MP1 | PX05MP2 |
| Carbon Cartridge | CB10MP1 | CB10MP2 |
| Maximum Flow | 30 L/min | 55 L/min |
| Connection | 1" / 25 mm | 1" / 25 mm |
Puretec specifies genuine replacement cartridges to maintain system performance, warranty and applicable standards.
Replacement timing depends on incoming water quality, household usage and treatment demand. Puretec's current cartridge guidance generally specifies replacement within the applicable service period, when rated capacity is reached, when flow becomes restricted or when unwanted taste or odour returns.
Replace the sediment cartridge according to particulate loading and the applicable Puretec service guidance.
Puretec recommends carbon cartridges be replaced within their service guidance, capacity limits or when taste or odour returns.
Inspect O-rings and sealing surfaces whenever the housings are opened for cartridge replacement.
Puretec offers the GR-WH230 Premium Care Kit specifically for the WH2-30 system.
The manufacturer states that the kit contains the components required for routine WH2-30 maintenance, including genuine Puretec cartridges, O-rings and food-grade lubricant.
The 5 micron polyspun sediment cartridge is installed first on the incoming-water side.
The 10 micron carbon block is installed downstream of the sediment stage.
The WH2-30 is intended for permanent installation on the mains-water supply before the treated water is distributed through the property.
Installation planning should account for isolation valves, the 25 mm connection, incoming pressure, mounting support and enough space beneath the housings for future cartridge replacement.
The standard WH2-30 is a wall-mounted filtration assembly rather than an enclosed FilterWall-style system.
Installation position should provide suitable protection and comply with the current Puretec installation requirements for the housings, bracket and connected plumbing.
If a fully covered whole-house filtration arrangement is preferred, consider a Puretec system specifically supplied with an enclosure rather than assuming the standard WH2-30 can be installed in any exposed location.
Puretec currently lists the WH2-30 with a 10-year warranty.
Puretec specifies genuine replacement cartridges to maintain system performance, warranty and applicable standards.
Order the Puretec WH2-30 for delivery to supported Australian locations where you already have a suitable installation arrangement.
The genuine Puretec GR-WH230 Premium Care Kit can be used for future cartridge and seal servicing.
Professional installation may be available in eligible Brisbane and Gold Coast service areas, subject to plumbing, pressure, access and site requirements.
Puretec currently lists the system as WH2-30-LF.
Yes. It is designed for point-of-entry filtration of mains water before the supply continues through the property.
Puretec lists a maximum system flow rate of 30 litres per minute.
The WH2-30 uses a 1" BSP / 25 mm connection.
Puretec's current WH2-30 product specification lists 520 kPa maximum pressure.
The first stage uses the Puretec PX05MP1 5 micron MaxiPlus sediment cartridge.
The second stage uses the Puretec CB10MP1 10 micron MaxiPlus carbon block cartridge.
Puretec lists sediment including dirt, rust, sand, silt, algae and suspended particulate material.
Puretec lists chlorine, unwanted taste, odour and sediment for the CB10MP1.
Puretec's current WH2-30 product page lists PFAS among the chemicals reduced by the complete system. No universal percentage should be assumed unless stated for the exact test and operating conditions.
No. The WH2-30 cartridge filtration assembly does not require electrical power.
No. The WH2-30 is a sediment-and-carbon filtration system and does not contain a water-softening or dedicated scale-control stage.
Follow Puretec's service guidance for the PX05MP1 and CB10MP1. Water quality, usage, flow restriction, cartridge capacity and the return of unwanted taste or odour can all affect practical service life.
Yes. Puretec lists the GR-WH230 Premium Care Kit specifically for WH2-30 systems and states that it includes genuine cartridges, O-rings and lubricant.
Puretec lists a 10-year warranty consisting of 1 year parts and labour plus 9 years parts only. Cartridges are excluded and warranty conditions apply.
Professional installation may be available in eligible Brisbane and Gold Coast service areas where the 25 mm plumbing connection, water pressure, mounting position and service access are suitable.
Purchase the Puretec WH2-30 without installation where you already have a suitable installer or servicing arrangement.
The system is matched with Puretec's manufacturer-listed PX05MP1 sediment cartridge and CB10MP1 carbon block.
Installed Today can also support eligible local installations where plumbing size, system pressure, mounting position and future service access are suitable.
The Puretec WH2-30 Whole House Water Filter is designed for mains-water properties requiring central sediment and carbon filtration with a maximum system flow rate of 30 L/min.
The current WH2-30-LF uses a 1" BSP / 25 mm connection and combines a PX05MP1 5 micron sediment cartridge with a CB10MP1 10 micron carbon block cartridge. Puretec currently lists the complete system for reduction of sediment, chlorine, unwanted taste and odour, chemicals and PFAS.
Before ordering, confirm that 30 L/min suits the property's peak demand, that the 25 mm connection matches the plumbing design and that the installation can remain within Puretec's current 520 kPa maximum-pressure specification. Where hardness reduction, scale control, UV treatment or another specialist process is required, select that treatment separately rather than assuming it is included in the standard WH2-30.
Buying a new hot water system, water filter, pump or plumbing product should be simple. Installed Today helps you compare the product, the supply-only price and the available installation options in one place, so you can choose what suits your home, budget and timing without the back and forth.
Whether you already know exactly what you need or you are still comparing options, we make it easier to order with confidence.
Choose the product on its own, or add installation where available. This gives you the flexibility to buy the way that suits you best.
See your product price upfront, then add the installation options or common extras you need before placing your order. No confusing quote forms just to understand your starting price.
Key specs, sizing details, warranty information, product features and suitability notes are shown clearly, so you can compare products properly before you buy.
Where relevant, you can add common installation extras such as valve kits, bases, electrical options, removal, access-related items or other site-specific upgrades before checkout.
Our product and installation options are selected with common local homes, water quality, plumbing layouts, access issues and replacement requirements in mind.
Add the product and selected extras to cart in one order, instead of trying to organise separate suppliers, installers and parts.
Not sure which product, size or installation option is right? Installed Today gives you a clearer path to choosing the right system before you order.
Installed Today is built for customers who want a faster, clearer and more convenient way to buy.
Instead of guessing what is included, waiting for basic pricing or trying to work out which extras are needed, you can review the product, compare your options and move forward with confidence.
Choose supply only if you just need the product.
Choose supplied and installed if you want the product installed where available.
Add common extras before checkout if your job needs additional parts or site-specific options.
It is a simpler way to organise the product and the parts of the job that matter most.
Installation availability, inclusions and add-ons vary by product type, site access, existing services, selected options and your property requirements. Some installations may require additional work, upgrades or checks before the job can proceed.
Same Day Delivery: Available in Brisbane and Gold Coast on select units ordered before 8:00am
Express Delivery: 1–4 business days
Standard Delivery: 2–8 business days
Same day delivery is available for selected hot water systems in Brisbane and Gold Coast metro areas when ordered before 8:00am, subject to stock availability, delivery capacity and suitable transport conditions.
Most hot water orders in metro areas are delivered quickly, with around 90% arriving within 1 business day.
Hot water systems cannot always be transported safely by courier during rain. Delivery timeframes may be affected when wet weather impacts safe handling, loading, unloading or transport conditions.
If your express delivery order takes longer than 1–4 business days, we will adjust the delivery timeframe to our standard 2–8 business days and refund your express shipping charge automatically.
We will send your delivery details as soon as your order has been dispatched.
Need help with your delivery? Contact our team and we’ll be happy to assist.
Helpful Installed Today guides covering whole home water filtration, drinking water filters, under-sink systems, reverse osmosis, Puretec filters and water quality.
