STAINLESS-STEEL SELF-PRIMING PRESSURE SYSTEM
Bianco BIA-INOX60CORE Stainless Steel Pressure Pump with NXT Controller
The Bianco BIA-INOX60CORE is a self-priming stainless-steel jet pressure system designed for smaller domestic water supply, rainwater-tank pressure systems, light garden irrigation, water transfer and compatible pressure-boosting applications.
White International's current product listing still uses the legacy-style name BIA-INOX60S2NXT in its page title, while the current product code and 2026 installation manual identify the system as BIA-INOX60CORE. Both refer to current order code 808394.
The current manufacturer manual specifies a 0.60kW fixed-speed jet pump, 62L/min maximum flow and 43m maximum head, paired with the Bianco NXT CORE electronic pressure controller.
Installed Today can offer the BIA-INOX60CORE as supply only or through eligible supplied-and-installed pathways in Brisbane and Gold Coast service areas, subject to the water source, suction conditions, pipework, electrical supply, pump location and required hydraulic performance.
Bianco INOX60CORE at a glance: order code 808394, 0.60kW self-priming jet pump, 62L/min maximum curve flow, 43m maximum head in the current 2026 manual, 4A maximum current, 1-inch BSP female suction inlet, 1-inch BSP male outlet, 2.2-bar factory start pressure, digitally adjustable start pressure from approximately 0.5 to 6.0 bar and 304 stainless-steel pump construction.
CURRENT PRODUCT IDENTITY
Is It BIA-INOX60S2NXT or BIA-INOX60CORE?
White International currently uses both names in its manufacturer material.
BIA-INOX60S2NXT
This remains the title used on White International's current online product listing for order code 808394.
BIA-INOX60CORE
This is the current product code shown on the manufacturer page, current data sheet and 2026 NXT InoxCORE installation manual.
For current technical information, the BIA-INOX60CORE designation is the clearer reference because it matches the current-generation manual and NXT CORE controller platform.
FIXED SPEED, AUTOMATIC CONTROL
Is the Bianco INOX60CORE Variable Speed?
No. The INOX60CORE uses a conventional fixed-speed asynchronous motor.
The NXT CORE controller provides automatic pressure-based starting, no-flow stopping and electronic protection, but it does not continuously vary motor speed to maintain a constant outlet pressure.
When system pressure falls below the configured start pressure, the controller starts the pump. The pump then runs at normal motor speed until water demand stops and flow falls below the controller's stop threshold.
Electronic automatic control is not the same as inverter-driven constant pressure. The INOX60CORE is a fixed-speed jet pump with an automatic digital controller.
KEY NUMBERS
Bianco INOX60CORE at a Glance
62L/min
Maximum Flow
43m
Current Manual Max Head
0.60kW
Motor Rating
4A
Maximum Current
MAXIMUM HEAD UPDATE
Is the Maximum Head 43m or 45m?
Current White International manufacturer material is not completely aligned.
The live product listing still displays 45m maximum head in its title and specification field.
The newer manufacturer data sheet and 2026 NXT InoxCORE installation manual list the INOX60CORE at 43m maximum head.
The page below uses 43m as the current technical figure because it is the value published in the newer current-generation manual. The older 45m value remains visible on White International's live product listing.
HYDRAULIC PERFORMANCE
Does the INOX60CORE Deliver 62L/Min at 43m Head?
No. Maximum flow and maximum head occur at different operating points.
The current manufacturer curve begins at approximately 43m head near zero flow. Available pump head falls as flow increases.
At higher flow rates, the pump therefore delivers substantially less than 43m head.
Do not convert 43m head into a pressure figure and assume that pressure remains available at 62L/min. Pump sizing needs to consider the required flow and pressure at the same operating point.
Suction lift, long pipe runs, undersized pipe, filters, fittings and building elevation further reduce the pressure available at the final outlet.
TECHNICAL SPECIFICATIONS
Bianco BIA-INOX60CORE Specifications
| Specification |
Current Manufacturer Detail |
| Brand |
Bianco Pumpz |
| Current Product Code |
BIA-INOX60CORE |
| Legacy / Listing Name |
BIA-INOX60S2NXT |
| Order Code |
808394 |
| System Type |
Self-priming fixed-speed jet pressure system with electronic controller |
| Maximum Flow |
62L/min |
| Maximum Head |
43m in the current 2026 manual; live product page still lists 45m |
| Motor Rating |
0.60kW / 0.8hp |
| Maximum Amperage |
4A |
| Electrical Supply |
220–240V AC, 50Hz, single phase |
| Motor Type |
Asynchronous TEFC motor with automatic-reset thermal overload |
| Pump IP Rating |
IPX4 in the current 2026 manual |
| Motor Insulation |
Class F |
| Pump Body |
304 stainless steel |
| Jet / Venturi / Diffuser / Impeller |
Glass-reinforced Noryl |
| Mechanical Seal |
Carbon / ceramic / nitrile |
| Suction Inlet |
1-inch BSP female |
| Discharge Outlet |
1-inch BSP male |
| Factory Start Pressure |
2.2 bar / approximately 220kPa |
| Adjustable Start Pressure |
Approximately 0.5–6.0 bar |
| Pump Stop |
When flow falls below approximately 0.5L/min |
| Maximum Pump-System Pressure |
6 bar |
| Working Temperature Range |
Approximately 2–40°C in the current technical table |
| Power Lead |
Approximately 1.5m, 10A-rated, three-pin plug |
| Current Manual Weight |
Approximately 12kg |
| Recommended Pressure Vessel |
3–18L for more efficient operation |
NXT CORE CONTROLLER
What Does the NXT CORE Controller Do?
The NXT CORE electronic controller automates normal pump operation.
The current system is factory-set to start the pump once pressure falls below approximately 2.2 bar.
The start pressure can be digitally adjusted between approximately 0.5 and 6.0 bar where the required duty and plumbing system suit that setting.
The pump stops once flow falls below approximately 0.5L/min.
- Digital system-pressure display
- Automatic starting on pressure drop
- Automatic stopping on low or no flow
- Dry-run protection
- Restart after water loss
- Restart after power interruption
- Frequent-start protection
- Plug-and-play pump connection
CONTROLLER RATINGS
What Are the NXT CORE Controller Limits?
The current 2026 InoxCORE manual lists the NXT CORE controller for approximately 240V, 50Hz operation with a maximum pump load of approximately 10A / 1.5kW.
The same manual lists a controller maximum pressure of 10 bar and maximum operating temperature of approximately 60°C.
The controller's 10-bar component rating is not the maximum pressure of the complete INOX60CORE pump system. The current pump technical table lists the complete pump system at a maximum of 6 bar.
CONTROLLER IP RATING
Is the NXT CORE Controller IP55 or IP65?
Current manufacturer documents conflict on this detail.
White International's live product page lists the NXT CORE controller as IP65.
The newer 2026 InoxCORE installation manual lists the controller as IP55.
Use the rating marked on the actual supplied controller and its accompanying documentation for the installation. The manufacturer sources currently do not publish one consistent IP figure.
Regardless of that discrepancy, the current installation manual still requires the complete pump and controller to be protected from rain, moisture, flooding and environmental extremes.
PRESSURE VESSEL
Does the INOX60CORE Need a Pressure Tank?
The NXT controller can operate the pressure system automatically, but Bianco's current manual recommends a 3L, 8L or 18L pressure vessel for more efficient domestic operation.
The vessel holds a small quantity of pressurised water and reduces unnecessary pump starts from small draw-offs or minor system leakage.
Bianco specifically links fewer pump starts with lower wasted energy and longer pump life.
For the INOX60CORE, the manufacturer's current pressure-vessel diagram lists approximately 2.97 bar as its example vessel gas-pressure setting based on two-thirds of expected maximum system pressure.
Do not assume the digital controller makes a pressure vessel pointless. The current manufacturer manual specifically recommends a 3–18L vessel for most efficient operation.
START FREQUENCY
Why Does Excessive Cycling Matter?
Bianco warns that the pump should not start more than approximately 20 times in one hour.
Very frequent starts can occur when there are small leaks, insufficient stored pressure volume or an installation that continually creates tiny water demands.
This is one reason the manufacturer recommends a small external pressure vessel for normal domestic systems.
DRY-RUN PROTECTION
What Happens if the Water Supply Runs Out?
The NXT CORE controller incorporates dry-run protection and restart functionality.
If usable water becomes unavailable, the controller can shut the pump down to prevent ongoing operation without water.
The controller can subsequently attempt to resume normal operation after the water supply returns.
Dry-run protection is a fault safeguard, not permission to operate the pump without water. Bianco states that dry operation damages the mechanical seal and can void warranty coverage.
SELF-PRIMING SUCTION
Can the INOX60CORE Draw Water Up From a Tank?
Yes. The INOX60CORE is a self-priming jet pump and can operate with the water source below the pump when the suction installation is properly designed, airtight and primed.
The current Bianco manual describes suction pipework as the most critical part of the installation because air leaks or excessive restriction can significantly affect pump performance.
- Use suction pipe at least as large as the pump inlet
- Keep the suction run as short as practical
- Maintain airtight connections
- Avoid pipework that traps air
- Prime the pump and suction pipe before first operation
- Use a suitable foot valve and intake screen where required
FOOT VALVE & INTAKE
When Does the INOX60CORE Need a Foot Valve?
The current manual states that suction piping drawing upwards by more than approximately 1 metre requires a non-return foot valve and intake screen.
Bianco also recommends:
- At least approximately 500mm of water above the intake
- Keeping the intake screen at least approximately 100mm above the tank or well bottom
- Avoiding positions where the intake can draw sediment
- Using the manufacturer's suction-pipe sizing guidance
These measures help maintain prime while reducing debris intake and suction losses.
SUCTION PIPE SIZE
Why Does Suction Pipe Size Matter?
Bianco's current manual warns that suction pipe that is too small, too long or required to lift water a significant height can cause a substantial reduction from the pump's rated duty.
The manufacturer's suction chart therefore increases recommended pipe diameter as the combined suction length and lift become more demanding.
A larger pump cannot compensate for a badly designed suction line. Air leaks, excessive lift and restrictive pipework can reduce flow, cause poor starting and increase reliability problems.
RAINWATER TANKS
Is the INOX60CORE Suitable for Rainwater Tanks?
Yes. Tank-fed domestic water supply is one of Bianco's stated applications.
The water needs to be clean enough for the pump and should not contain significant sand, sludge or abrasive contamination.
The INOX60CORE provides pressure from the tank but does not by itself provide automatic rainwater-to-mains changeover.
Automatic mains backup requires a separate compatible rainwater-management arrangement. The pump controller manages the pump; it does not select between tank water and mains water.
MAINS BOOSTING
Can the INOX60CORE Be Connected Directly to Mains Water?
Bianco identifies pressure boosting as an application, but its current installation manual states that direct connection of this type of pump to the mains water supply is not recommended.
Where mains pressure is inadequate, the manufacturer's stated best-practice approach is an isolating or break tank from which the pressure pump draws water.
The final plumbing arrangement needs to be selected for the actual property.
CLEAN WATER REQUIREMENTS
What Water Can the INOX60CORE Pump?
The pump is designed for clean water.
Bianco warns that sand and mineral contamination can adversely affect both the hydraulic pump and electronic controller.
The current installation manual lists an acceptable water pH range of approximately 6.5 to 8.5.
The manufacturer also specifically states that the InoxCORE pumps are not suitable for spa or pool water.
DRINKING WATER APPROVAL
Is the Bianco INOX60CORE Suitable for Drinking-Water Systems?
Yes. The current NXT InoxCORE manual identifies the pump range as meeting AS/NZS 4020 drinking-water approval requirements for products coming into contact with water intended for human consumption.
This relates to the materials used in the pump and water-contact components.
It does not mean the pressure pump filters, disinfects or makes contaminated rainwater suitable for drinking.
ELECTRICAL CONNECTION
How Is the INOX60CORE Powered?
The current pump specification is approximately 220–240V AC, 50Hz single phase with a maximum current of approximately 4A.
The 2026 manufacturer manual lists an approximately 1.5m 10A-rated lead with an Australian three-pin plug.
Bianco requires connection to a suitable electrical outlet with residual-current protection.
If no suitable power outlet exists in the required location, any new power point, circuit extension or other fixed electrical installation work is additional.
INSTALLATION LOCATION
Where Should the INOX60CORE Be Installed?
The pump should be located on a firm base as close as practical to the water source and near a suitable electrical supply.
Where rigid pipe fittings are used, Bianco recommends securing the pump on a suitable concrete tile, concrete base or similar stable support.
Pipework should be independently supported so its weight does not place unnecessary stress on the pump casing or electronic controller.
WEATHER PROTECTION
Can the INOX60CORE Be Installed Outdoors?
The current manufacturer manual requires the pump and controller to be protected from rain and moisture and from extremes of temperature.
Bianco specifies a weatherproof, free-draining and well-ventilated enclosure that also protects against flooding, chemicals, vermin, insects and excessive dust.
Do not treat the pump or controller IP rating as approval for unrestricted outdoor exposure. White International still requires environmental protection around the complete pressure system.
HOUSEHOLD SIZING
How Many Taps Can the INOX60CORE Supply?
White International's current product listing uses six taps as a product-selection guide.
A fixed tap number is not a reliable substitute for hydraulic sizing because taps, showers and irrigation outlets can have very different flow requirements.
Correct selection should consider:
- Simultaneous outlet flow
- Required pressure
- Suction lift
- Pipe diameter
- Pipe length
- Property elevation
- Filters and restrictions
- Garden or irrigation demand
Six taps is a manufacturer selection guide rather than a guarantee that six high-flow fixtures will operate simultaneously at maximum pressure.
CURRENT INOXCORE RANGE
How Does the INOX60CORE Compare With the Other InoxCORE Models?
| Specification |
INOX45CORE |
INOX60CORE |
INOX90CORE |
| Maximum Head |
40m |
43m |
50m |
| Maximum Flow |
58L/min |
62L/min |
79L/min |
| Motor Rating |
0.45kW |
0.60kW |
0.75kW |
| Maximum Current |
3.5A |
4A |
6A |
| Current Manual Weight |
9kg |
12kg |
13kg |
The INOX60CORE sits between the compact INOX45CORE and the higher-output INOX90CORE, providing a moderate increase in hydraulic performance without moving to the largest model in the range.
WARRANTY
Bianco BIA-INOX60CORE Warranty
Current White International sources do not presently show one consistent warranty period for order code 808394.
| Current Manufacturer Source |
Warranty Information |
| Live Product Listing |
24 months / 2 years |
| Current 2026 NXT InoxCORE Manual |
Displays a 3-year Bianco NXT warranty badge |
| Manual Warranty Terms |
State that the warranty period indicated on the document applies, subject to the stated conditions |
The newer current-generation manual therefore presents a three-year warranty for the NXT InoxCORE range, while White International's live 808394 product page still lists 24 months.
Confirm the warranty documentation supplied with the actual unit at the time of purchase. Until White International aligns these two current sources, the warranty should not be represented as though the manufacturer publishes only one period.
SUPPLY ONLY
Buy the Bianco INOX60CORE Supply Only
Choose supply only where a suitable plumber, pump installer or other appropriately qualified installer is already arranged.
The pump-only price does not automatically include:
- Plumbing installation
- Suction-pipe alterations
- Delivery-pipe alterations
- Foot valve or intake screen
- Isolation valves
- Unions or flexible connectors
- External pressure tank
- Filtration or strainers
- Automatic mains-water changeover
- Electrical outlet or circuit work
- Pump-base alterations
- Weather-protection enclosure
- Existing pump removal
- Off-site disposal
SUPPLY & INSTALL
Bianco INOX60CORE Supplied & Installed
Eligible Brisbane and Gold Coast customers can select a supplied-and-installed pathway where the water source, existing pipework and installation location suit the INOX60CORE.
Water Source Check
The installer confirms that the water is sufficiently clean and that the proposed suction arrangement can maintain reliable prime.
Hydraulic Check
Suction size, delivery pipework, elevation and simultaneous water demand need to sit within the current 62L/min and 43m pump-performance envelope.
Location & Power Check
The pump needs firm support, appropriate weather protection, suitable electrical supply and access for future service or replacement.
STANDARD INSTALLATION
What Can Change the Installation Scope?
A straightforward replacement assumes the existing pump location, water source, pipework and electrical supply are accessible and suitable.
Additional work can apply where:
- The pump is being relocated
- Suction pipework leaks or is undersized
- A foot valve or intake screen is required
- Delivery pipework needs alteration
- Isolation valves or unions require replacement
- A pressure vessel is being added
- The tank contains heavy sediment
- Automatic mains-water backup is required
- A new electrical outlet is required
- A support base or weather enclosure is required
- Access falls outside the standard installation conditions
INSTALLATION AREAS
Bianco Pressure Pump Installation in Brisbane & Gold Coast
Installed Today can provide supplied-and-installed pathways across eligible Brisbane and Gold Coast service areas where the INOX60CORE and the required installation scope are available.
Brisbane
Gold Coast
Supply-only ordering is also suitable for customers who already have an appropriate installer arranged and only require the pressure system supplied.
MID-RANGE STAINLESS-STEEL JET PRESSURE SYSTEM
Why Choose the Bianco INOX60CORE?
The INOX60CORE sits in the middle of Bianco's current stainless-steel InoxCORE range and combines moderate domestic hydraulic performance with the convenience of an electronic automatic controller.
Current 2026 manufacturer data lists 62L/min maximum flow, 43m maximum head, a 0.60kW motor, 4A maximum current, 2.2-bar factory start pressure, digitally adjustable starting from approximately 0.5 to 6.0 bar and 304 stainless-steel pump construction.
Its main installation considerations are suction-line design, required water pressure and flow, water cleanliness, weather protection, electrical supply and whether an external pressure vessel or automatic mains-water changeover is required.
COMMON QUESTIONS
Questions About the Bianco INOX60CORE
Is BIA-INOX60S2NXT Still the Current Name?
White International still uses BIA-INOX60S2NXT in the title of its current product page, but the current product code, data sheet and 2026 manual identify order code 808394 as BIA-INOX60CORE.
What Is the Order Code?
The current manufacturer order code is 808394.
Is It a Jet Pump?
Yes. It is a self-priming stainless-steel jet pressure pump.
Is It Variable Speed?
No. It uses a fixed-speed motor with an automatic electronic NXT CORE controller.
What Is the Maximum Flow?
The current manufacturer documentation lists 62L/min.
What Is the Maximum Head?
The newer current manual lists 43m. White International's live product page still shows 45m.
Why Does the Older Listing Say 45m?
White International's current online product metadata has not been fully aligned with the newer InoxCORE technical manual. The page therefore uses the newer manual's 43m figure while noting the discrepancy.
Does It Deliver 62L/Min at 43m Head?
No. Maximum head and maximum flow occur at different points on the pump curve.
What Is the Factory Start Pressure?
The NXT CORE controller is preset to approximately 2.2 bar or 220kPa.
Can the Start Pressure Be Adjusted?
Yes. The current manual lists digital adjustment from approximately 0.5 to 6.0 bar.
When Does the Pump Stop?
The controller stops the pump when flow falls below approximately 0.5L/min.
What Size Is the Motor?
The INOX60CORE uses a 0.60kW / 0.8hp motor.
What Current Does It Draw?
The current manual lists approximately 4A maximum amperage.
What Power Supply Does It Use?
The pump uses approximately 220–240V AC, 50Hz single-phase electricity.
Does It Come With a Power Lead?
Yes. The current manual lists an approximately 1.5m 10A-rated lead with a three-pin plug.
What Size Is the Inlet?
The suction inlet is 1-inch BSP female.
What Size Is the Outlet?
The discharge outlet is 1-inch BSP male.
What Is the Pump Body Made From?
The current manual lists 304 stainless steel.
Does It Have Dry-Run Protection?
Yes. The NXT CORE controller includes run-dry protection and restart functions.
Can It Run Dry Safely?
No. The protection system is a safeguard. Bianco states that dry operation damages the mechanical seal and can void warranty coverage.
Can It Draw From a Rainwater Tank?
Yes, where the water is clean and the suction installation is airtight, correctly sized and properly primed.
When Does It Need a Foot Valve?
The current manual states that suction pipe drawing upward more than approximately one metre requires a non-return foot valve and intake screen.
Does It Need an External Pressure Tank?
The controller can operate the pump automatically without a traditional pressure-switch arrangement, but Bianco recommends a 3L, 8L or 18L pressure vessel for more efficient domestic operation.
Can It Pump Pool or Spa Water?
No. The current manufacturer manual specifically states that the pump is not suitable for pool or spa water.
Is It Drinking-Water Approved?
Yes. The current manufacturer manual identifies the NXT InoxCORE range as meeting AS/NZS 4020 drinking-water approval requirements.
Does Drinking-Water Approval Mean It Filters the Water?
No. The approval relates to the materials used in water-contact components. The pump does not purify the source water.
Can It Boost Mains Water Directly?
Bianco's current manual states that direct connection to mains water is not recommended and identifies an isolating or break tank as best practice where mains pressure is inadequate.
Can It Be Installed Outdoors?
It can form part of an outdoor water system when installed in a weatherproof, free-draining and well-ventilated enclosure as required by Bianco.
Is the Controller IP55 or IP65?
Current manufacturer sources conflict. The current live product page lists IP65 while the newer 2026 InoxCORE manual lists IP55. The rating marked on the actual supplied controller should be used for the installation.
How Many Taps Can It Supply?
White International lists six taps as a selection guide. Actual suitability depends on simultaneous flow, required pressure, suction conditions, pipework and elevation.
What Is the Maximum Pump-System Pressure?
The current InoxCORE technical table lists 6 bar maximum pressure for the pump system.
What Is the Controller Maximum Pressure?
The current NXT CORE controller guide lists 10 bar. That is a controller component rating rather than the maximum pressure of the complete pump system.
What Is the Warranty?
Current manufacturer sources conflict. White International's live product page lists 24 months, while the newer 2026 NXT InoxCORE manual displays a three-year warranty badge and states that the warranty period indicated on the document applies. Confirm the documentation supplied with the actual unit at purchase.
Can I Buy the INOX60CORE Supply Only?
Yes. Supply-only ordering suits customers who already have an appropriate installer arranged.
Can Installed Today Install It?
Eligible Brisbane and Gold Coast properties can select a supplied-and-installed pathway where the water source, suction conditions, pipework, electrical supply and pump location are suitable.
FINAL CHECK
Is the Bianco INOX60CORE Right for Your Property?
The Bianco BIA-INOX60CORE is primarily suited to smaller domestic clean-water applications needing a self-priming automatic jet pressure system with more hydraulic capacity than the INOX45CORE but less than the INOX90CORE.
Current manufacturer documentation lists 62L/min maximum flow, 43m maximum head, a 0.60kW motor, 4A maximum current, 1-inch suction and discharge connections, a 2.2-bar factory start pressure and digital adjustment from approximately 0.5 to 6.0 bar.
Before ordering, check the required simultaneous flow and pressure, water source, suction lift, pipe diameter and length, tank cleanliness, electrical supply, weather protection, external pressure-vessel requirements and whether automatic mains-water changeover is needed.
For supply only, arrange a suitable installer. For eligible Brisbane and Gold Coast properties, select the matching supplied-and-installed pathway and any required plumbing, pressure-vessel, filtration, electrical, weather-protection, removal or access add-ons before checkout.
