PURETEC HYBRID FACTORY MAINTENANCE KIT
Puretec HR-G7R2 Factory Service Kit – Suits Hybrid G7 & R2
The Puretec HR-G7R2 is the genuine manufacturer-listed maintenance kit for compatible Puretec Hybrid G7 and Hybrid R2 filtration and ultraviolet systems.
The kit combines the two 20-inch MaxiPlus replacement cartridges with the main UV service components used by these systems: PL05MP2, DP10MP2, RL6 UV lamp, RQS6 quartz sleeve, food-grade lubricant and two O-rings.
The G7 and R2 use the same filtration and UV component combination, making the HR-G7R2 the correct factory maintenance kit for either configuration.
Quick answer:
the Puretec HR-G7R2 suits Hybrid G7 and Hybrid R2 systems. It includes PL05MP2 + DP10MP2, an RL6 46W UV lamp, an RQS6 quartz sleeve, food-grade lubricant and two O-rings. Puretec specifies cartridge replacement every 6 months, UV lamp replacement annually and regular quartz-sleeve inspection.
KIT AT A GLANCE
Puretec HR-G7R2 Key Details
2 Cartridges
PL05MP2 + DP10MP2
```
RL6
46W UV Lamp
RQS6
Quartz Sleeve
2 O-Rings
Plus Food-Grade Lubricant
```
WHAT'S INCLUDED
Factory Service Kit Contents
PL05MP2
5 micron, 4.5" × 20" washable pleated polyester sediment cartridge.
```
DP10MP2
10 micron, 4.5" × 20" dual-purpose carbon-impregnated cartridge for sediment, chlorine taste, unwanted taste and odour reduction.
RL6 UV Lamp
46W high-output ultraviolet replacement lamp specified for compatible Hybrid G, R and P Series systems.
RQS6 Quartz Sleeve
Replacement quartz sleeve used around the RL6 lamp inside the Hybrid UV chamber.
Food-Grade Lubricant
Included for applicable sealing surfaces and O-ring maintenance during the service process.
2 O-Rings
Two replacement O-rings are included in the manufacturer-listed HR-G7R2 kit.
```
DUAL FILTRATION + UV
Designed for the G7 & R2 Treatment Sequence
The Hybrid G7 and R2 use two cartridge stages before ultraviolet treatment.
Stage 1 uses the PL05MP2 for washable 5 micron sediment filtration. Stage 2 uses the DP10MP2 for additional sediment filtration together with chlorine, unwanted taste and odour reduction.
The filtered water then passes through the Hybrid UV chamber using the RL6 lamp and RQS6 quartz sleeve.
STAGE 1
PL05MP2 5 Micron Washable Sediment Cartridge
The PL05MP2 is the first filtration stage specified for both the Hybrid G7 and Hybrid R2.
Puretec manufactures the cartridge from durable non-woven reusable polyester media pleated around a polypropylene support core. The pleated design provides a large filtration surface area for sediment collection.
5 Micron
Provides nominal 5 micron sediment filtration.
```
4.5" × 20"
Uses Puretec's large 20-inch MaxiPlus cartridge format.
180 L/min
Puretec lists the individual PL05MP2 cartridge at up to 180 litres per minute.
Washable
Puretec specifies the pleated cartridge as washable and reusable where appropriate.
Sediment
Designed to reduce dirt, rust, sand, silt and suspended particulate material.
Pre-Filtration
Reduces sediment loading before water reaches the dual-purpose second stage and UV chamber.
```
STAGE 2
DP10MP2 Dual-Purpose Carbon Cartridge
The DP10MP2 is installed as the second cartridge stage in the G7 and R2.
Rather than using a conventional bonded carbon block, Puretec manufactures the DP10MP2 from carbon-impregnated non-cellulose pleated media.
This allows the cartridge to combine sediment filtration with carbon treatment in a single 20-inch MaxiPlus cartridge.
10 Micron
Nominal particulate filtration rating of 10 micron.
```
4.5" × 20"
Uses the same 20-inch MaxiPlus format as the first-stage cartridge.
110 L/min
Puretec lists the individual DP10MP2 cartridge at up to 110 litres per minute.
Chlorine
Provides chlorine taste-and-odour reduction in applicable water supplies.
Taste & Odour
Designed to reduce unwanted taste and odour through carbon treatment.
Sediment
The pleated media also provides additional particulate filtration.
```
UV LAMP
RL6 46W High-Output UV Lamp
The HR-G7R2 includes one genuine Puretec RL6 46W high-output ultraviolet lamp.
The RL6 is the manufacturer-specified replacement UV lamp for both the Hybrid G7 and Hybrid R2.
Puretec specifies annual UV lamp replacement.
The Hybrid controller tracks lamp life, and Puretec lists the applicable UV lamp service life as 365 days. The lamp-life timer should be reset after replacement according to the system maintenance procedure.
QUARTZ SLEEVE
RQS6 Replacement Quartz Sleeve
The RQS6 is a quartz sleeve, not a filter cartridge.
It surrounds the RL6 lamp inside the UV chamber and separates the electrical lamp from the water while allowing ultraviolet light to pass through into the water stream.
Puretec recommends inspecting the quartz sleeve regularly, approximately every 3 months depending on source-water quality, to check for deposits or fouling.
The sleeve can be cleaned where required and should be replaced if it is damaged or cannot be restored to a suitably clear condition.
COMPATIBILITY
Which Systems Does HR-G7R2 Suit?
Puretec Hybrid G7
Puretec lists HR-G7R2 as the maintenance kit for existing Hybrid G7 systems using PL05MP2, DP10MP2, RL6 and RQS6.
```
Puretec Hybrid R2
The same kit is also specified for the current Hybrid R2 indoor system using the identical replacement cartridge and UV components.
```
Confirm the full Hybrid model before ordering.
Other Hybrid models can look similar but use different cartridge sizes, cartridge combinations or maintenance kits.
HYBRID G7
Factory Maintenance for Existing Hybrid G7 Systems
The complete Hybrid G7 is currently listed by Puretec as a discontinued system, but Puretec continues to list HR-G7R2 as its replacement maintenance kit.
The G7 uses:
- Stage 1 – PL05MP2
- Stage 2 – DP10MP2
- UV lamp – RL6
- Quartz sleeve – RQS6
- 1" BSP [25 mm] system connection
- Weather-protected G Series cabinet configuration
HYBRID R2
Factory Maintenance for Hybrid R2 Systems
The Hybrid R2 uses the same filtration and UV replacement components as the G7.
The R2 uses a reversible mounting arrangement for indoor installations and must be installed where it is protected from weather.
- Stage 1 – PL05MP2
- Stage 2 – DP10MP2
- UV lamp – RL6
- Quartz sleeve – RQS6
- 1" BSP [25 mm] system connection
- Protected indoor R Series installation
G7 VS R2
Same Service Kit, Different Installation Configuration
| Feature |
Hybrid G7 |
Hybrid R2 |
| Maintenance Kit |
HR-G7R2 |
HR-G7R2 |
| Stage 1 |
PL05MP2 |
PL05MP2 |
| Stage 2 |
DP10MP2 |
DP10MP2 |
| UV Lamp |
RL6 |
RL6 |
| Quartz Sleeve |
RQS6 |
RQS6 |
| Connection |
1" BSP [25 mm] |
1" BSP [25 mm] |
| Installation Style |
Weather-protected G Series cabinet |
Indoor, weather-protected R Series |
SYSTEM FLOW
Hybrid G7 & R2 UV Flow Ratings
Puretec specifies different flow rates according to the ultraviolet dose delivered by the complete G7 and R2 systems.
| UV Dose |
Puretec Listed Flow |
| 40 mJ/cm² |
54 L/min |
| 30 mJ/cm² |
70 L/min |
| 16 mJ/cm² |
130 L/min |
Puretec identifies 30 mJ/cm² as the industry-standard UV dose reference for drinking-water applications. The correct system performance depends on source-water clarity and the required UV dose.
CARTRIDGE FLOW
Individual Cartridge Flow Is Not the Complete-System Flow
180 L/min
PL05MP2 Cartridge
```
110 L/min
DP10MP2 Cartridge
70 L/min
G7/R2 at 30 mJ/cm²
```
Individual cartridge ratings should not be used as the complete Hybrid system rating. The UV dose requirement, cartridges, housings, water quality, pipework and available pressure all affect system performance.
KIT SPECIFICATIONS
Puretec HR-G7R2 Technical Details
| Component |
Specification |
| Kit Model |
HR-G7R2 |
| Compatibility |
Puretec Hybrid G7 and Hybrid R2 |
| Stage 1 Cartridge |
PL05MP2 – 5 micron, 4.5" × 20" washable pleated sediment |
| Stage 2 Cartridge |
DP10MP2 – 10 micron, 4.5" × 20" dual-purpose sediment and carbon |
| UV Lamp |
RL6 – 46W high-output UV replacement lamp |
| Quartz Sleeve |
RQS6 |
| Lubricant |
Food-grade lubricant included |
| O-Rings |
2 pieces included |
| Cartridge Replacement |
Every 6 months |
| UV Lamp Replacement |
Annually |
| Quartz Sleeve Inspection |
Approximately every 3 months depending on water quality |
MAINTENANCE SCHEDULE
Different Components Have Different Service Requirements
PL05MP2 & DP10MP2
Puretec's Hybrid G/R maintenance guide specifies replacement of the filtration cartridges every 6 months.
```
RL6 UV Lamp
Puretec specifies UV lamp replacement every 12 months.
RQS6 Quartz Sleeve
Inspect approximately every 3 months, depending on source-water quality, and clean or replace when required.
```
Water conditions can also require additional inspection or earlier filtration maintenance where sediment loading or quartz-sleeve fouling is unusually high.
CARTRIDGE REPLACEMENT
Correct Cartridge Order Matters
Puretec identifies the cartridge nearest the incoming water supply as Stage 1.
1. PL05MP2
Install the 5 micron washable pleated sediment cartridge nearest the water inlet.
```
2. DP10MP2
Install the 10 micron dual-purpose carbon cartridge in the second housing before the UV chamber.
```
Do not reverse the filtration stages.
The cartridges perform different treatment functions and should be installed in the sequence specified by Puretec.
SERVICE PROCESS
What Is Involved in a Hybrid G7 or R2 Service?
- Confirm the installed system is a Hybrid G7 or Hybrid R2
- Disconnect electrical power before UV servicing
- Turn off the incoming water supply
- Relieve water pressure before opening filter housings
- Allow UV components to cool before handling
- Remove the existing PL05MP2 and DP10MP2 cartridges
- Clean filter bowls with soap and warm water
- Rinse filter bowls thoroughly
- Inspect O-rings and sealing surfaces
- Use food-grade silicone lubricant where required
- Install PL05MP2 in stage one
- Install DP10MP2 in stage two
- Replace the RL6 UV lamp at its scheduled service
- Inspect, clean or replace the RQS6 quartz sleeve as required
- Restore the water supply gradually and purge trapped air
- Flush the filtration system for 1–2 minutes
- Check the complete system for leaks
- Restore power and reset the UV lamp-life timer after lamp replacement
UV SERVICE CARE
Important Lamp & Quartz Sleeve Handling
The ultraviolet section requires additional care beyond a normal cartridge replacement.
Disconnect electrical power and isolate the water supply before UV servicing.
Puretec also instructs users to release system pressure and allow the UV components to cool before handling.
Avoid touching the glass lamp or quartz surfaces unnecessarily. Marks and fingerprints can interfere with UV transmission and should be cleaned according to the applicable maintenance procedure.
The quartz sleeve is glass and should be handled carefully during removal and installation.
AFTER SERVICING
Flush & Check the System Before Returning It to Use
Puretec's Hybrid maintenance procedure specifies gradually restoring the water supply with a downstream tap open so trapped air can escape.
After new cartridges are installed, allow water to run for approximately 1–2 minutes to flush the filtration system, then close the downstream tap and check the Hybrid unit for leaks.
Puretec also specifies a 1–2 minute flush after periods of non-use longer than two weeks. After very extended periods of non-use, cartridge replacement may be required depending on condition.
WHAT IS NOT INCLUDED
Some Cleaning Products & Repairs Remain Separate
The HR-G7R2 includes PL05MP2, DP10MP2, RL6, RQS6, food-grade lubricant and two O-rings.
Separate maintenance products such as dedicated quartz-sleeve cleaner or filter-housing sanitiser should not be treated as included unless specifically supplied with the order.
Existing faults are separate from scheduled consumable maintenance.
Damaged filter housings, electrical controllers, pumps, valves, fittings, pipework or other system components may require additional parts or labour.
BEFORE ORDERING
Check These Details First
- Your installed system is a Puretec Hybrid G7 or R2
- Stage one requires PL05MP2
- Stage two requires DP10MP2
- Your UV system uses an RL6 lamp
- Your UV chamber uses an RQS6 quartz sleeve
- You require the full factory kit rather than cartridges only
- The filtration housings and UV assembly are accessible
- The system can be safely isolated from water and electrical power
DIY OR PROFESSIONAL SERVICE
Can the HR-G7R2 Be Installed Yourself?
Puretec provides maintenance instructions for compatible Hybrid systems, but the HR-G7R2 service involves both pressurised filtration housings and electrically powered ultraviolet equipment.
The cartridges must be installed in the correct order, the housings resealed correctly, and the UV lamp and quartz sleeve handled without damaging the glass components.
Professional servicing may be appropriate where you are not experienced with Hybrid UV maintenance.
Existing leaks, damaged seals, electrical faults, seized housings, cracked quartz sleeves, pump faults or associated plumbing issues can require additional work beyond installing the factory kit.
ORDERING OPTIONS
Choose How You Want to Order
Supply Only
Order the genuine Puretec HR-G7R2 for delivery to supported Australian locations where you have confirmed your Hybrid system model.
```
Full Factory Kit
Receive both filtration cartridges, the RL6 lamp, RQS6 quartz sleeve, food-grade lubricant and two O-rings in one manufacturer-listed maintenance package.
Professional Service Option
Professional Hybrid cartridge and UV servicing may be available in eligible Brisbane and Gold Coast service areas.
```
COMMON QUESTIONS
Questions About the Puretec HR-G7R2 Factory Service Kit
What Systems Does the HR-G7R2 Suit?
Puretec specifies HR-G7R2 for Hybrid G7 and Hybrid R2 systems.
Does It Still Suit an Existing Hybrid G7?
Yes. Puretec currently lists the complete G7 as discontinued but continues to list HR-G7R2 as its maintenance kit.
What Filter Cartridges Are Included?
The kit contains one PL05MP2 and one DP10MP2.
What Order Do the Cartridges Go In?
PL05MP2 is stage one nearest the water inlet, followed by DP10MP2 as stage two.
What Size Are the Cartridges?
Both use Puretec's 4.5" × 20" MaxiPlus format.
Is the PL05MP2 Washable?
Yes. Puretec specifies the PL05MP2 as a washable pleated polyester sediment cartridge.
What Does the DP10MP2 Do?
It combines sediment filtration with carbon treatment for chlorine taste, unwanted taste and odour reduction.
Is a UV Lamp Included?
Yes. The kit includes one genuine RL6 46W high-output UV lamp.
Is a Quartz Sleeve Included?
Yes. One RQS6 quartz sleeve is included.
Is RQS6 a Filter Cartridge?
No. RQS6 is the quartz glass sleeve used around the UV lamp inside the ultraviolet chamber.
Are O-Rings Included?
Yes. Puretec lists two O-rings as part of the HR-G7R2 kit.
Is Food-Grade Lubricant Included?
Yes. Puretec lists food-grade lubricant as part of the factory kit contents.
How Often Should the Cartridges Be Replaced?
Puretec's Hybrid G/R maintenance guide specifies cartridge replacement every 6 months.
How Often Should the RL6 Lamp Be Replaced?
Puretec specifies replacement annually.
How Often Should the Quartz Sleeve Be Checked?
Puretec recommends inspection approximately every 3 months depending on source-water quality.
Can Installed Today Service the System?
Professional Hybrid cartridge and UV maintenance may be available in eligible Brisbane and Gold Coast service areas where the system is accessible and in serviceable condition.
WHY INSTALLED TODAY
Order the Correct Puretec Hybrid Maintenance Kit
Supply First
Purchase the genuine Puretec HR-G7R2 without adding installation where you already have your own servicing arrangement.
```
Clearly Defined Contents
The listing identifies both cartridges, the RL6 lamp, RQS6 quartz sleeve, lubricant and O-rings rather than describing the product as a generic maintenance set.
Installation Capability
If you prefer professional servicing, Installed Today may also be able to complete the filtration and UV maintenance in selected local service areas.
```
FINAL CHECK
Is the Puretec HR-G7R2 the Right Kit for Your Hybrid System?
The Puretec HR-G7R2 Factory Service Kit is the manufacturer-listed maintenance kit for Puretec Hybrid G7 and Hybrid R2 systems.
It contains PL05MP2, DP10MP2, RL6 46W UV lamp, RQS6 quartz sleeve, food-grade lubricant and two O-rings, covering the principal filtration and ultraviolet consumables specified for these systems.
Before ordering, confirm that your installed unit is a Hybrid G7 or R2. Puretec specifies cartridge replacement every 6 months, annual UV lamp replacement and quartz-sleeve inspection approximately every 3 months depending on water quality. During servicing, isolate both the water supply and electrical power, maintain the correct cartridge sequence and check the complete system for leaks before returning it to normal operation.
